Sealing Mechanism

In: Science

Submitted By hassaanch
Words 374
Pages 2
Sealing mechanism:
1) Radial shaft seals:
Radial shaft seals, also known as lip seals, are used to seal rotary elements, such as a shaft or rotating bore. It is widely used for in applications of full submersion of seal and shaft.

- Aviods leakage sufficientally
- Prevent contamination which can harm components of the system.

Operating conditions ( pressurized conditions) :
Pressure ≤ 10 bar
Temp -30 to 140oc

Lip ring with spiral spring for radial preloading
Short but pressure stiff flexible, spring- preloaded sealing lip.

2) Stuffing box ( Gland seal) :
The stuffing box prevents sea water from entering the UV hull. In many cases the stuffing box is mounted inboard near the point the shaft exits the hull.
The "box" is a cylindrical assembly, typically of bronze, comprising a sleeve threaded on one end to accept adjusting and locking nuts. A sound stuffing box installation is critical to safety because failure can admit a catastrophic volume of water into the UV
In a common type of stuffing box, rings of braided fiber, known as shaft packing or gland packing, form a seal between the shaft and the stuffing box. Ideally, the compression is just enough to make the seal both watertight when the shaft is stationary and drip slightly when the shaft is turning.
3) End face mechanical seal:
An end face mechanical seal uses both rigid and flexible elements that maintain contact at a sealing interface and slide on each other, allowing a rotating element to pass through a sealed case.
Types of face seals:
O rings
E rings
C rings

- O rings:
The O-ring may be used in static applications or in dynamic applications where there is relative motion between the parts and the O-ring.
The seal is designed to have a point contact between the O-ring and sealing faces. This allows…...

Similar Documents

Control Mechanisms

...Starbucks: Control Mechanisms Starbucks: Control Mechanisms Starbucks is the leading coffee company in the world. They have locations around the world, many of which are independently owned. In order for the corporation to keep accurate records on the stores, they have implemented many types of controls. Four types of controls used in the Corporation are Bureaucratic Control, Budgetary Control, Financial Control, and Concurrent Control. Bureaucratic Control Bureaucratic controls are control higher up the chart of an organization, have authority to dictate policies and procedures. This control starts with the board of directors, followed by the Chief Executive Officer, vice presidents, and continues as necessary. Starbucks’ bureaucratic manages through policy rules and number of operating procedures, which helps to determine the behavior of divisions, functions, and individuals. The essential of Bureaucratic Controls, the profit motive on a larger-scale enterprise tend to help the business grow and achieve a higher level of profit. The stock market valuation of the firm is the influence by expectation of future sales and profit, produce negative growth. The cost motive the economics of scale could have an effect of increasing the productive capacity of the business, and help increase the profit margins. The market power object can increase job market dominance and increase pricing power. The risk concept provide the business expansion......

Words: 978 - Pages: 4

Network Mechanisms

...Network Mechanisms This paper will define and describe the differences in mechanisms that make up a network system. It will include topologies and connection mediums, as well as the advantages and disadvantages associated with these network mechanisms. Topologies and connection mediums that will be addressed are the following: Topologies: • Mesh • Bus • Ring • Star Connection Mediums: • Ethernet • Token Ring • FIDDI • Wireless Mesh Topology A mesh topology consists of two types, full mesh and partial mesh. Full mesh topology interconnects all systems to each other. This allows for redundancy if one connection is severed. With partial mesh topology only some workstations are interconnected to other computer systems while; others are only connected with systems that an exchange of data occurs (Mitchell, 2011). The advantages and disadvantages of a mesh topology are: Advantages: Disadvantages: Provides redundant paths between systems Time and material to implement The network can be expanded without disruption to current users. Cost to implement (many connections) Dedicated links for transmitting data Complicated implementation Bus Topology A bus topology uses a common backbone that directly connects each system. The backbone consists of a single cable that all transmissions are sent across by the systems that are attached (Mitchell, 2011). The advantages and disadvantages of a bus topology are: Advantages: Disadvantages: Easy to......

Words: 988 - Pages: 4

Coping Mechanism

...effectively coping with a particular stress, while what they are really doing is creating many others. Also, since each factor has the power to influence the others, the true form of the transaction theory can only be captured when time is included as one of the variables. Longitudinal studies are crucial in order to truly reflect the long term effects and processes that take place within the whole coping mechanism. Research Paradigm INPUT PROCESS OUTPUT Fig. 1. This paradigm shows the procedure that the researcher decided to use in conducting the study on the coping mechanism on the problems encountered by the HRM practicumers of SMCL. Statement of the Problem This study is about the coping mechanism on the problems encountered by HRM student who are having their on-the-job training as a requirement in their curriculum. And it seeks to gather the facts and information about the problem. Specifically, the following questions seek to answer: What are the coping mechanisms on the difficulties that the Hotel and Restaurant Management practicumers have in to solve their problems? Significance of the Study The significance of having the ON THE JOB TRAINING of the HRM students would deal with the attention and the task that is being needed to takes place with reality and the certainty that is training is the process of providing employees with specific skills or......

Words: 9135 - Pages: 37

Defense Mechanisms

...being a murderer and being responsible for the death of his family. At the end, Andrew became mentally ill himself for refusing to accept reality. This is the story of the Movie “Shutter Island” which is an example for what is called “Defense Mechanisms” and how they have a huge effect on our lives. Due to the fact that everyday people are faced with problems, stress, conflict and emotional pain, the mind needs to be protected against these painful feelings. As a result, “Defense Mechanisms” play an important role during these times in order to protect the mind from Stress and Anxiety by “unconsciously” denying reality and refusing it. Although Defense Mechanisms have positive side that they protect the individual against painful thoughts and experiences but using them without awareness can be destructive. “Defense Mechanisms” were researched by Sigmund Freud who’s an Austrian neurologist who became well known as “Father of Psychoanalysis”. Freud defined “Defense Mechanisms” as people’s unconscious behavior to cope with distress and anxiety; in other words they are ways that people use “unconsciously” to escape from painful experiences which they do not want to deal with or think about. Freud identified some types of “Defense Mechanisms” that can be used by a person while trying to defend himself against anxiety. These types include: 1. Denial It is the refusal to accept reality, in which the person convinces himself that the problem does not exist or pretend that it did......

Words: 2819 - Pages: 12

Defense Mechanisms

...wholly negative thing. It has let me move past the incident instead of dwelling on it and preventing me from having a caring relationship with my family. On the other hand, involvement in the church was and continues to be an important part of my family’s life and I’ve missed a lot of that. Denial is defined as, “arguing against an anxiety provoking stimuli by stating it doesn't exist,” according to A common example is when a person receives a doctor’s diagnosis that they have cancer. Instead of accepting the news, they pass off the statements as untrue. This protects the person, because they are choosing not to acknowledge their diagnosis, while eliminating all feelings of sadness and hurt. I’ve noticed this defense mechanism at work in the actions of my mother. She has difficulty maintaining a budget. She spends well beyond her means but refuses to acknowledge the fact. Just recently she purchased a convertible sports car. What you have to know is that her only income is social security and a very small pension from my deceased father’s career. When we asked if she could afford the car and insurance she said there was plenty in her budget to cover the expense. This would have been true is she had no other financial commitments. Things like food, utilities and medical expenses. We have repeatedly tried to sit down with her and help lay out a budget, but she always finds a way to avoid or change the topic and pretend that everything is ok. Her home is......

Words: 1326 - Pages: 6

Control Mechanism

...Control Mechanisms of Boeing Boeing’s internal controls ensure that the executive leadership and personnel reasonably achieve specified business objectives within tolerable business risk limits. Boeing’s control environment consists of interrelated components, including governance by a functioning of the board of directors (BOD), management’s philosophy and operating styles, assignment of authority, and integrity and ethics values. Boeing’s internal control environment is a reflection of the organizations consciousness, philosophies, and behaviors that emanate throughout the organization from the top down. Continual review, evaluation, and amendments of existing internal controls ensure Boeing’s business goals are met that will ensure a successful future (Corporate Governance Principles, 2013). Effectiveness of Boeing’s Control Mechanisms “The global economy is becoming more integrated than ever before” (International Management, 2011, p. 200). Therefore, Boeing’s control mechanisms enabled them to establish a remarkably diverse team of business partners, employees, and community relations. Boeing’s commitment of providing a welcoming, respectful, and engaging work environment with the possibilities of growth for employees has motivated productivity and innovation. Boeing is creatively building character and discipline in tomorrow’s future by securing values in today’s culture. Reactions to Boeing’s Control Mechanisms Boeing strives to be an industry......

Words: 415 - Pages: 2

Control Mechanisms

...Control Mechanisms: Use and Reaction at Chipotle Mexican Grill Control Mechanisms: Use and Reaction at Chipotle Mexican Grill Control is essential for any company to ensure their business plan is being executed efficiently to achieve its corporate goals. Part of the organization's planning includes which control mechanism best suits the business' core competency. This paper will study how Chipotle Mexican Grill utilizes Control Mechanisms and the reactions from employees and customers and to what degree Chipotle can monitor and control execution of its business plan, will determine the long-term viability of the company’s very existence. Leadership Vision Steve Ells, chef and founder of Chipotle is an inspired leader with a strong desire only to serve delicious and healthy ‘Food with Integrity.’ Integrity in the Chipotle vernacular means a strong commitment to small farmers by serving only naturally raised animals and organically grown vegetables. Culture Chipotle believes their crew members are just as important as their food for sustained success.......

Words: 1358 - Pages: 6

Control Mechanism

...Control Mechanism For Best Buy Joanne Forde MGT/330 March 7, 2011 Dorothy Galiger Control Mechanism For Best Buy An effective control system within any organization must provide detailed information that is both valuable in its measure and consistent in its delivery. Such qualities of a control system are essential for management to harness it for the greater good of the organization. Control systems must be a fluid expansion of the control aspect of the organization’s strategic planning. Best Buy is a good example of a company that utilizes control systems to assist in company operations. These controls are not without their negative consequences, but for the most part, they serve as a beneficial tool for the company in achieving its goals. Control systems specify standards of performance, monitor, and measure company performance, and use data collected to compare the company outcomes to internal standards. Controls also assist in making steps toward continued improvement by reinforcing successful techniques and revising the less successful ones. Best Buy uses four distinct types of controls to maintain and drive the success of their organization: Feed forward control, market control, financial control, and Bureaucratic control. Feed Forward Control is aimed toward preventing problems before they begin by setting standards in place to reduce company loss. For example, Best Buy offers customers a return policy, but only gives cash refund with a receipt or...

Words: 1882 - Pages: 8

Control Mechanisms

...MGT 330 –Control Mechanism Paper Control Mechanisms Control mechanisms have many purposes in business management. The control mechanism of employee incentives directly influences the management function of leading (Ganly, 2010). Control mechanisms serve many important purposes; they allow an organization to protect their values they have created as well as the profit of the organization from reduction by competitors, partners, or customers. Control mechanisms add for better predictability, this in turn helps form better business models for an organization. This paper evaluates six different control mechanisms among six different organizations. The control mechanisms are: job descriptions, program evaluations, pay scale, communication, performance evaluations, and disciplinary procedures. Job Descriptions Consolidated Care depends on detailed job descriptions for their employees to be an effective organization. Job descriptions are effective because they establish lines of authority and areas of responsibility. Consolidated Care uses job descriptions not only as an outline of expectations of the employee but also a tool to provide an evaluation criterion and provide motivation. Consolidated Care employees respond both positive and negative to their job descriptions. Job descriptions also provide employees with the guidance of who to go to when a problem arises or questions occur. Though, there are some employees who react negative to job description. These employees......

Words: 1630 - Pages: 7

Bonding and Sealing Plastic Windows

...Marine Application Guide Bonding and Sealing Organic Windows Application Description Most of the organic glazing materials used in boat building are either clear acrylic sheet (PMMA), widely marketed under trade names such as Perspex and Plexiglas (the latter manufactured by Rohm and Haas), or polycarbonate (PC), marketed by Bayer GmbH as Makrolon and by General Electric as Lexan or scratch-proof Margard. All plastic glazing products possess certain characteristics that must be clearly understood before they are installed or bonded with adhesives. In general, incorrectly installed plastic glazing panels are prone to environmental stress cracking (ESC). This can be aggravated by the use of the wrong adhesives. Sika Transportation_99 Plastic glazing products have a higher coefficient of thermal expansion than conventional glass. Therefore, when designing glazing installations, an expansion gap of at least 10 mm all round the periphery must be incorporated between the window rebate and the plastic glazing panel to accommodate thermal movement. Similarly, any clearance holes for fixing screws must be drilled oversize; slightly larger than the diameter of the screw shank. To minimise the risk of environmental stress cracking, flat sheets of plastic glazing material should be installed completely flat; they should not be forced to take up a curvature by the use of mechanical fastenings. When the design calls for curved glazing panels,......

Words: 1234 - Pages: 5

Control Mechanism

...Control mechanisms are regularly used with successful organizations to maintain and adjust processes and practices. Wal-Mart is a company that applies control mechanisms to its business functions to remain a global leader in the industry. The four types of control mechanisms that Wal-Mart puts into action are market control, clan control, audit control, and performance standards. Market Control is “the ability of buyers or sellers to exert influence over the price or quantity of a good, service, or commodity exchanged in a market”. ( the next mechanism used is Clan control it “relies on values, beliefs, corporate culture, shared norms, and informal relationships to regulate employee behaviors and facilitate the reaching of organizational goals” (strategic Audit control is the process of self examination as it relates to accounts and products. Lastly, Performance standards are an organizational approved set of requirements, goals and expectations that employees must meet. These four mechanisms are paramount in today’s business world for effectively and efficiently doing business to meet organizational goals. Wal-Mart has a responsibility to its employees, vendors and the customers to make changes where needed. The economy has influenced the frequency of the changes and requires constant monitoring. The application of these four mechanisms is why Wal-Mart remains a leader in the retail industry. Compare and Contrast Control Mechanisms ......

Words: 2219 - Pages: 9

Control Mechanisms

...Control Mechanisms for Home Depot Jaclyn Fix, Kelly Gomez, William Miller, and Nicholas Johnston MGT/330 November 14, 2011 Bassam Asfoor Control Mechanisms for Home Depot The four functions of management are planning, organizing, leading, and controlling (Bateman & Snell, 2009). The four types of controls used by Home Depot significantly affect the four functions of management within the organization. Setting performance standards is a part of the planning process while measuring them is part of the control function. Managing performance standards enables the company to have more visibility on what works and what does not in both policy and product. Rectifying problems also plays into each of the functions of management, largely in leading. Home Depot’s corporate and executive levels must monitor the company and identify any potential problems or issues that need to be addressed. Four Types of Control Mechanisms The four types of control mechanisms used for The Home Depot are setting performance standards, measure performance; compare performance against the standards, and taking actions to correct deficiency. The depot sets performance standards during orientation, the standards given are what the company expects from every individual who works for the company. There are also standards given to each individual according to what department he or she works in. For example employees are sales associates, sales specialists, or......

Words: 1793 - Pages: 8

Peak Sealing Technology

...Peak Sealing Technology Yash Malhotra 1st March, 2016 Peak Sealing Technology is a recognized adhesive industry leader in innovation and quality. Its products are widely used for manufacturing and packaging applications. The adhesive market was really competitive when it came to sealing tapes for cartons. These products were available in different varieties and at a range of prices. Though PST’s K-2 tape was a superior product, it competed with other products that did not provide the same quality to the consumers but were much more economical. Hence, Peak Sealing Technology was in a dilemma of whether or not to produce a more economical and a low quality product to compete better with its peers and acquire a better market share due its brand name. The main issue that Peak Sealing Technology faced was of having a lack of competitors in its product’s range. This lead to the K-2 tape competing against much inferior products in the market. If PST decides to introduce an economical product in the market, it could face a variety of issues: * It would lower the brand value of the company and it would not be considered as a premium product * The price war will eventually decrease profitability * Its new product in the market might cannibalize the sale of its superior products Hence, I recommend that Peak Sealing Technology should not introduce an economical product in the market, it could market its product better by educating price sensitive consumers of lower......

Words: 259 - Pages: 2

Defensive Mechanism

...Defense Mechanisms Primitive Defense Mechanisms 1. Denial * Someone told you that your loved one died but, you refused to believe it, you still keep her clothes clean and wait for her to come home. * A friend told you that she saw your boyfriend with another girl in the cinema, and you refuse to believe it, you make yourself believe that maybe it was just his friend, sister, or cousin. * You’re friends told you to join a singing contest but, you refused, because you think you will never succeed, and there are better singers than you that will also join. 2. Acting Out * Your girlfriend broke up with you and you got mad that you punched the mirror and somehow it made you feel better. * Someone says or does something that makes you feel offended in some way. You lash out at them with loud verbal taunts or you attack them physically * You ask your parents or guardians to do something. They say no. You do that “fake crying” that often results in your parents giving in to your request. 3. Projection * You have a strong dislike for someone; you might instead believe that he or she does not like you. * Your group presentation failed because you didn’t bring some materials that are needed but, you blamed another person. * John was caught by her wife having an affair but, he blames his wife because she doesn’t have time for him anyway. Less Primitive Defense Mechanism 1. Repression * A child who is abused by a parent later has no......

Words: 350 - Pages: 2

Trust Mechanisms

...Reputation Based Trust Management 3 Policy-Based Trust Mechanism Policy based trust mechanisms are used in those situations where firm security is required. Policy based trust mechanisms are targeted at those systems where performance is guided by complex rules and they should be adoptive to changes in the system easily [1]. In this bidirectional mechanism of trust, trust is established by the exchange of credentials in case of semantic web where those parties interact with each other which are primarily unknown to each other [2]. In environments where access control decisions are critical this system is frequently implemented [3]. Access or denial is given by analyzing the credentials which have been provided by unknown entities and implementation of set of trust policies on the provided credentials. Use of third party services (which are trusted) for the authentication of given credentials is also possible in this mechanism [3]. In sensitive environments where critical transactions are being made, it is an ideal system. 4 Reputation Based Trust Mechanism The rating or reputation based system guides the people towards decision making process that is what product to trust and what not to. By implementing this reputation based system trustworthy sellers could be encouraged while dishonest ones could be dejected. There are a lot of online markets which have implemented the reputation based trust mechanism to promote trust in online transactions. Different......

Words: 3887 - Pages: 16

Nicola Pannelli | 爱奇艺2018最新版 | 3:24 16 And Pregnant - From Student to Teen Mom storybooth 4,023,848 views 3 months ago